Bailey Motor Equipment Co.
Bailey Motor Equipment Co.
10501 South Orange Ave.
Suite 126 Orlando, FL 32824
Toll Free: 800.394.8134
Phone: 407.422.8134 •
Fax: 407.841.2471
Email: mitch@baileymotorequip.com
Website: www.baileymotorequip.com
Print Back

Enclosed Sentinel 300P.
Input supply 10/120/220/240 VAC (50 Hz/60 Hz).
Output 10 A at 12/24 V.
Analog ammeter and voltmeter.
Unit of Measure

Specifications

Model Number

 N/A ESNTL300PM

Outputs x3 (x4 for Non-CAN Configurations)

 N/A 1 x SPCO (RL1), 1 x SPNC (RL2), 1 x SPNO (RL3), dry/volt-free contacts (common feed for RL1, RL2 & RL3)

Standard Models (Non-CAN Configurations)

 N/A 1 x SPNC (RL4), dry/volt-free contacts standard output functions (charge fail, AC fail, low battery volts, high battery volts) are NFPA 110 compliant.

Inputs x2

 N/A Closed to negative DC to activate, configurable function

Industry Standards

 N/A CE cULus NFPA 110

Electrical Connections

 N/A
Electrical Connections for Sentinel 300P Programmable Switch Mode Battery Chargers

Power Supply

Alternate Current (AC) Operating Voltage

 N/A 95 to 250 V

Operating Frequency

 N/A 47 to 63 Hz

Direct Current (DC) Charge Output

Direct Current (DC) Nominal Voltage1 N/A 12 V24 V

Maximum Current Limit

 N/A 10 A

Voltage Ripple

 N/A <1 %

Line Regulation

 N/A <2 %

Load Regulation

 N/A <2 %

Rating (All Relays)

Maximum Current Rating at 30 Direct Current (DC) Voltage2 N/A 1 A

Standards for Maximum Current Rating at 30 Direct Current (DC) Voltage

 N/A UL Class 2

Physical

Operating Temperature

 N/A -40 to 60 ºC-40 to 140 ºF

Display Viewability (Liquid Crystal Display (LCD) Models)

 N/A 0 to 50 ºC32 to 122 ºF

Relative Humidity

 N/A 20 to 90 %

Electrical Safety

 N/A 2006/95/EC

Electromagnetic Compatibility

 N/A 2004/108/EC EN 55022 Class B (EN 61000-6-1, EN 61000-6-3)

UL Approvals

 N/A BBGQ: UL1236, CSA22.2 no. 107.2 BBHH: UL1236 SE

Dimensions

Overall Width (W)

 N/A 6.50 in165 mm

Overall Height (H1)

 N/A 11.81 in300 mm

Overall Height (H2)

 N/A 3.15 in80 mm

Overall Depth (D1)

 N/A 4.92 in125 mm

Overall Depth (D2)

 N/A 5.12 in130 mm

Fixing Holes (X)

 N/A 2.50 in63.5 mm

Fixing Holes (Y)

 N/A 11.25 in285.5 mm

Weight

 N/A 4.4 to 4.6 lb2.0 to 2.1 kg

Standard Output Calibration

Output Calibration Information

 N/A

Battery type is selected by circuit board DIP switches or SNTL300P-PCSUITE configuration software.

Calibration figures at 20 ºC. If temperature compensation is enabled, and remote SNTL-RTC temperaturesensor connected, output voltage automatically varies by 3 mV per cell per 1 ºC deviation from 20 ºC, within the range -10 to +50 ºC. Increasing temperatures give decreasing outputs; decreasing temperatures give increasing outputs.

Output Calibration Specification Table

 N/A
Output Calibration Specification Table for Sentinel 300P Programmable Switch Mode Battery Chargers

AutoBoost

AutoBoost

 N/A

Triggered automatically on low charge levels, or manually by remote switch, AutoBoost temporarily increases the charge voltage before returning to float mode. Equalizing battery cell charge without overcharge and gassing, AutoBoost maximizes cell capacity and life.

Temperature Compensation

Temperature Compensation

 N/A

For remote charger control, and signaling of charge fail, high/low battery volts and mains fail faults. Standard output functions are NFPA 110 compliant. Non-standard input/output functions available to special order.

Flexible Configuration

Flexible Configuration

 N/A

For remote charger control, and signaling of charge fail, high/low battery volts and mains fail faults. Standard output functions are NFPA 110 compliant. Non-standard input/output functions available to special order.

Inputs and Outputs

Inputs and Outputs

 N/A

Tested and approved by UL to: UL1236 - Battery chargers for charging engine-starting batteries, and CSA22.2 No. 107.2 - Battery chargers.

In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our specifications and designs at any time. Murphy products and the Murphy logo are registered and/or common law trademarks of Enovation Controls, LLC. This document, including textual matter and illustrations, is copyright protected by Enovation Controls, LLC, with all rights reserved. (c) 2015 Enovation Controls, LLC. A copy of the warranty may be viewed or printed.

Dimensions for reference only. Use actual product for mounting template. For safe heat dissipation, mount product in orientation shown, with minimum air gap clearance of 1.5 in./40 mm above/below and 1.0 in./25 mm at each side.

Display, Instrumentation and Communication

Display, Instrumentation and Communication

 N/A

Tested and approved by UL to: UL1236 - Battery chargers for charging engine-starting batteries, and CSA22.2 No. 107.2 - Battery chargers.

In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our specifications and designs at any time. Murphy products and the Murphy logo are registered and/or common law trademarks of Enovation Controls, LLC. This document, including textual matter and illustrations, is copyright protected by Enovation Controls, LLC, with all rights reserved. (c) 2015 Enovation Controls, LLC. A copy of the warranty may be viewed or printed.

Dimensions for reference only. Use actual product for mounting template. For safe heat dissipation, mount product in orientation shown, with minimum air gap clearance of 1.5 in./40 mm above/below and 1.0 in./25 mm at each side.

Note

Note

 N/A

Tested and approved by UL to: UL1236 - Battery chargers for charging engine-starting batteries, and CSA22.2 No. 107.2 - Battery chargers.

In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our specifications and designs at any time. Murphy products and the Murphy logo are registered and/or common law trademarks of Enovation Controls, LLC. This document, including textual matter and illustrations, is copyright protected by Enovation Controls, LLC, with all rights reserved. (c) 2015 Enovation Controls, LLC. A copy of the warranty may be viewed or printed.

Dimensions for reference only. Use actual product for mounting template. For safe heat dissipation, mount product in orientation shown, with minimum air gap clearance of 1.5 in./40 mm above/below and 1.0 in./25 mm at each side.
  • 1 Programmable
  • 2 Resistive load